High Performance Grease

MOLYSLIP AS40 40%
GELLED LUBRICATING OIL WITH 40% MoS2 15% GRAPHITE POWDER CORROSION & RUST INHIBITORS PLUS EXTREME PRESSURE COMPOUNDS.

Exceptional load carrying capacity OF 140,000 PSI. FAR ABOVE THE YIELD POINT OF MOST METALS minimum friction and excellent anti-wear TO LOADS characteristics. Has a steady working range from -20°C to 150°C.

This outstanding grease is loaded with extreme pressure and corrosion resistant additives.

With Extreme pressure load capacity

Formulated to provide bearing extra protection or prolonged use between service and avoid routine greasing

High Oxidation stability

Provides rust prevention and minimises fretting corrosion. Good resistance again both fresh and SALT water so suitable for marine use.

Suitable for ball and roller bearings, General chassis and machine lubrication. Slides, screws, valves stems and shaft carrier bearings, perfect for sail riggings and marine pulleys.

No degreasing is required before treatment, but parts should be cleaned. Apply with brush or spatula.

Recommended for: pre-treatment of new or reconditioned plain bearings, gears, rings, cams, and valve stems.

In machine shops for lathe centres, slide screws & all controls.

For cylinder plungers and turbine relay valves, for bulkheads mechanisms, for reducing heat produced in heavy loaded bearings.

Other applications are out door tools wheel barrows and recreation equipment swing sets porch swings.

Just great for all sorts of odd jobs.

It is very heat resistant with the melt point at 200 deg C or 500 deg F

Working temp of -20 C to +150 C

High speed bearing grease.
Lithium based with MoS2 and extreme pressure compounds. Exceptional load carrying capacity with minimum friction and excellent anti-wear characteristics. Has a steady working range from -50°C to 150°C.

This outstanding grease is loaded with extreme pressure and corrosion resistant additives.

With Extreme pressure load capacity

Formulated to provide bearing extra protection or prolonged use between service and avoid routine greasing

High Oxidation stability

Provides rust prevention and minimises fretting corrosion. Good resistance again both fresh and SALT water so suitable for marine use.

Suitable for ball and roller bearings, General chassis and machine lubrication. Slides, screws, valves stems and shaft carrier bearings, perfect for sail riggings and marine pulleys.

I have used it on a friends boat for his prop shaft and over a year later still going strong this is perfectly suited for all transport applications.

Other applications are out door tools wheel barrows and recreation equipment swing sets porch swings.

Just great for all sorts of odd jobs.

It is very heat resistant with the melt point at 195 deg C or 450 deg F

Working temp of -30 C to +150 C

Also available in the grease gun Cartridge(same price as the 450gram tin) and available in 5 kilo and 12.5 kilo kegs.


People who bought this item also bought:

Great for use on break callipers, exhaust and head bolts battery terminals.

Now I don't recommend it but I know a Japanese rally team mix it with oil and use it in the engine, Personally I would stick to using it on bolts.

Here only at 70% off retail. for 100 gram tubes

An anti-seize compound and a lubricant perform entirely different functions although many anti-seize products have lubricating properties, especially at higher temperatures. In environmentally adverse conditions such as high humidity and salinity, extreme pressure, acidic atmospheres or excessive temperatures, metals can fuse or weld together. The chief culprit is corrosion, particularly in marine surroundings. Molyslip anti-seize products are designed to provide an insulating layer between metals so that dismantling and routine maintenance are free from breakage of fused parts. This problem is especially onerous on threads and shackles. A single application of Copaslip (often misspelled as copperslip or coppaslip) or Alumslip will stop metal fusion for many years.

Copaslip®
Copaslip® (often misspelled as copperslip or coppaslip) - the original anti-seize compound. Available in leaded or lead-free versions.
It is a very high temperature (up to 1100°C) anti-seize assembly compound, bentone based non-melt grease with copper, pure lead paste or polybutene, and anti-corrosion additives.

Saves time, money and energy

In the Automotive Trade
...prevents squealing on disc brake pads, allows for trouble-free dismantling of chassis mountings, cylinder heads, inlet and exhaust fittings etc.

In the Marine Industry
...protects moving parts against the arduous and corrosive marine environment.

In the Petroleum Industry
...in drilling, production and refining processes, saves hours of downtime.

In the Workshop
...the honing and plating action protects metal in conditions where conventional lubricants break down.

Copaslip ®

In Manufacturing
...for maintenance of high temperature plant up to 1100°C.

In the Chemical Industry
...saves valuable man hours in the routine maintenance and dismantling of retorts, boiler covers, valves and furnace parts.

In Agriculture
...ensures trouble-free maintenance of tractors, harrows, ploughs, mowers and agricultural accessories.

Also available 500 gram and 5 kilo tins.

500 GRAM
Nickel anti-seize assembly compound is specially formulated to protect against seizure even under extreme conditions of pressure and temperature. Also a highly effective thread lubricant and protective. Designed for same applications as Copaslip® (often misspelled as copperslip or coppaslip) but where there is a prejudice against the presence of copper. Temperature range up to minus -200°C to 1350°C.

This amazing calcium based grease has corrosion resistant additives.

Main uses would be for application on Stainless steel exhaust systems to prevent seizure under even the most extreme conditions.

With Extreme exposure resistance.

High Oxidation resistance.

Provides rust prevention and minimises fretting corrosion. Good resistance again both fresh and SALT water so suitable for marine use.

Great on wheel lug nuts also good for use on exhaust system bolts, painting on break fluid pipes to prevent corrosion break callipers, spark plugs, glow plugs battery terminals.

Also good for sealing bolt seats against intrusion of contaminants, filling surface irregularities, and preventing leaks.

Any where exposed to heat and the elements chassis welds and body bolts.

Spare tyre caddy the list of uses is endless.

Other applications are out door tools wheel barrows and recreation equipment swing sets porch swings.

Just great for all sorts of odd jobs.

It is very heat resistant with the melt point at 1350° C or nearly 3000° F

Working temp of sub zero temp -200 to 1350°C

Contains no Lead

Almost the same as the original formula with nearly identical properties just with out lead

Great for use on break callipers, exhaust and head bolts battery terminals.

Now I don't recommend it but I know a Japanese rally team mix it with oil and use it in the engine.

Personal I would stick to using it on bolts.

An anti-seize compound and a lubricant perform entirely different functions although many anti-seize products have lubricating properties, especially at higher temperatures. In environmentally adverse conditions such as high humidity and salinity, extreme pressure, acidic atmospheres or excessive temperatures, metals can fuse or weld together. The chief culprit is corrosion, particularly in marine surroundings. Molyslip anti-seize products are designed to provide an insulating layer between metals so that dismantling and routine maintenance are free from breakage of fused parts. This problem is especially onerous on threads and shackles. A single application of Copaslip (often misspelled as copperslip or coppaslip) or Alumslip will stop metal fusion for many years.

Copaslip®
Copaslip® (often misspelled as copperslip or coppaslip) - the original anti-seize compound. Available in leaded or lead-free versions.
It is a very high temperature (up to 1100°C) anti-seize assembly compound, bentone based non-melt grease with copper, pure lead paste or polybutene, and anti-corrosion additives.


Saves time, money and energy

In the Automotive Trade
...prevents squealing on disc brake pads, allows for trouble-free dismantling of chassis
mountings, cylinder heads, inlet and exhaust fittings etc.

In the Marine Industry
...protects moving parts against the arduous and corrosive marine environment.

In the Petroleum Industry
...in drilling, production and refining processes, saves hours of downtime.

In the Workshop
...the honing and plating action protects metal in conditions where conventional lubricants break down.

Copaslip ®

In Manufacturing
...for maintenance of high temperature plant up to 1100°C.

In the Chemical Industry
...saves valuable man hours in the routine maintenance and dismantling of retorts, boiler covers, valves and furnace parts.

In Agriculture
...ensures trouble-free maintenance of tractors, harrows, ploughs, mowers and agricultural accessories.


Also available 500 gram and 5 kilo tins.

500 GRAM

Alumslip anti-seize assembly compound is specially formulated to protect against seizure even under extreme conditions of pressure and temperature. Also a highly effective thread lubricant and protective. Designed for same applications as Copaslip® (often misspelled as copperslip or coppaslip) but where there is a prejudice against the presence of copper. Temperature range up to 1100°C.

This amazing grease has corrosion resistant additives with extreme exposure resistance &
High Oxidation resistance.

Provides rust prevention and minimises fretting corrosion. Good resistance again both fresh and SALT water so suitable for marine use.

Great on wheel lug nuts also good for use on exhaust system bolts, painting on break fluid pipes to prevent corrosion break calipers, spark plugs, glow plugs battery terminals.

Also good for sealing bolt seats against intrusion of contaminants, filling surface irregularities, and preventing leaks.

Any where exposed to heat and the elements chassis welds and body bolts.

Spare tyre caddy the list of uses is endless.

Other applications are out door tools wheel barrows and recreation equipment swing sets porch swings.

Just great for all sorts of odd jobs.

It is very heat resistant with the melt point at 1100 deg C or 2200 deg F

Working temp of any sub zero temp to 1100 C